Acrylamide/sodium acryloyldimethyltaurate copolymer, 0.80
isohexadecane, polysorbate 80
Aluminum starch octenylsuccinate a.n.
PROCEDURE: Add phase A to secondary vessel and start mixing.
Add milled phase B with continued mixing. When uniform, add
phase C. Heat to 80°C. Add phase D with mixing. Add phase E and
mix until fully dissolved. Add the water and glycerin of phase F to the
main vessel and start mixing. Add the tetrasodium EDTA, then add
the xanthan gum. Heat to 80°C. When both batches are homogeneous and at 80°C, slowly add phase ABCDE to phase F with mixing.
Homogenize for 3 minutes, then start cooling. When batch is < 50°C,
add phase G ingredients one by one with mixing. When the batch is
again uniform, add deionized water to correct for evaporative losses.
Continue mixing until smooth. PROPERTIES ( 25°C): Appearance—
smooth, light beige lotion; Viscosity— 5,000– 7,000 mPa∙s ( 20 rpm,
Brk, RV DV-II, T-D, after 24 hours at room temperature).
Highlighting Bronzer Cream for Face and Body
Floramac 10 (Flora-tech) (Ethyl macadamiate) 12.00
Octyldodecyl Olivate (Sandream Impact) 10.00
SD Sugar Crystal (Sandream Impact) (Cetearyl alcohol/ 3.00
sucrose distearate/behenyl alchohol/glyceryl stearate/
hydrogenated lecithin/squalane/ceramide 3)
Versagel ME 1600 (Calumet Specialty Products Partners) 2.00
(Hydrogenated polyisobutene, ethylene/propylene/styrene
copolymer, butylene/ethylene/styrene copolymer)
Ceraphyl 847 (Ashland) 2.00
(Octyldodecyl stearoyl stearate)
Arlacel 165 (Croda) 1.50
(Glyceryl stearate; PEG- 100 stearate)
Soybean Oil (Jeen) (Glycine soja oil) 1.00
Jeecide Phenoxy (Jeen) (Phenoxyehanol) 1.00
DP Bronze M5000 (Sandream Impact) (Mica, Fe2O3) 10.00
Distilled water 20.00
Propylene Glycol (UPI Chem) (Propylene glycol) 4.00
Aloe Moist (Terry) (Aloe barbadensis leaf juice (and) 1.00
glycerin (and) glyceryl acrylate (and) propylene glycol)
Ketrol CG (CP Kelco) (Xanthan gum) 0.20
Permethyl 99A (Presperse) (Isododecane) 14.00
Distilled water 17. 70
Juiciliscious Fragrance (Bell Flavors & Fragrances, Inc.) 0.40
Rose Callus Stem Cell (Sandream Impact) (Rosa damascena0.20
callus culture extract (and) 1,2 hexanediol (and) sodium
hyaluronate (and) ethylhexyl glycerin (and) water)
PROCEDURE: Preheat phase A to 65-70°C and propeller mix until solution is dissolved and homogeneous. Gradually add phase B
and continue mixing until thoroughly incorporated. Premix phase
C in a separate beaker, maintaining temperature at 65°C, until a
uniform and thickened solution is present. Add phase C to A &
B and homogenize for 10 minutes, maintaining temperature and
turbulent flow. Next add phase D to A, B & C – homogenize an additional 5 minutes keeping the beaker covered. Premix phase E in a
small beaker at room temperature. Remove large beaker from heat
and homogenize slowly while bringing down to room temperature. Add phase E to remaining phases, homogenizing 10 minutes
to ensure the formation of a smooth emulsion.
Pore Minimizing Leave on Dream Mask
Sensient Cosmetic Technologies
Water q.s.p. 100
Base O/W 097 (Sensient) (Ceteareth- 25 (and) 13.00
PEG-2 stearate (and) paraffinum liquidum (and)
hydrogenated coconut oil (and) cetyl alcohol (and)
Covasterol (Sensient) (Glyceryl isostearate (and) isostearyl 5.00
alcohol (and) brassica campestris (rapeseed) sterol (and)
butyrospermum parkii butter (and) candellia cera)
Isononooyl isononoate 7.00
Caprylic/capric triglyceride 5.00
Covacryl MV 60 (Sensient) (Sodium polyacrylate) 1.00
Ethylhexyl glycerin (and) phenoxyethanol 1.00
PROCEDURE: Heat phase A to 75-80°C. Heat phase B to 75-80°C.
Once uniform and both phases are at temperature add phase B to
phase A using a homogenizer to emulsify. Homogenize for 5 minutes.
Change to a propeller mixing and cool to 50°C. At 50°C add phase C
mix until uniform. Once uniform add Phase D and mix until uniform.
PROPERTIES: Viscosity at 24hrs—TC, @20RPM, 39,500 cps. •